پروگرامر و دیباگر st-link مخصوص میکروهای سری st - اورجینال و کیفیت بالا و قابلیت آپدیت
st linkST-LINK V2For STM8 STM32 Debugger ,Programmer, stlink کیفیت بالا و قابلیت اپدیت - های کپی
پروگرامر و دیباگر st-link مخصوص میکروهای سری st - های کپی و کیفیت بالا و قابلیت آپدیت
چیپ اصلی این پروگرامر آیسی STM32 میباشد و آیسی GD نیست. این پروگرامر از کیفیت بالایی برخوردار میباشد و دارای بافر هست و قابلیت آپدیت شدن را دارد و تا تاریخ 16-7-2023 آپدیت انجام شده و مشکلی ندارد. این پروگرامر های کپی می باشد.
پروگرامر و دیباگر مخصوص میکروکنترلرهای خانواده stm
قابلیت کار با کامپایلرهای keil,IAR
مشتریان گرامی میتوانید با نسخه ای که در قسمت دانلود ویژه ارائه شده است اپدیت کنید که در نرم افزار کیل با خطا مواجه نشوید.
پشتیباتی از تمامی خانواده میکروکنترلر های stm
STM8A,STM8L,STM8S
STM32F,STM32L,STM32W,STM32H
https://www.st.com/internet/evalboard/product/251168.jsp
https://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/DM00027105.pdf
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
In addition to providing the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL features digital isolation between the PC and the target application board. It also withstands voltages of up to 2500 VRMS.
STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.
STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.
- 5 V power supplied by a USB connector
- USB 2.0 full speed compatible interface
- USB standard A to mini B cable
- SWIM specific features
- 1.65 V to 5.5 V application voltage supported on SWIM interface
- SWIM low-speed and high-speed modes supported
- SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
- SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
- SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
- JTAG/serial wire debugging (SWD) specific features
- 1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
- JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
- JTAG supported
- SWD and serial wire viewer (SWV) communication supported
- Direct firmware update feature supported (DFU)
- Status LED which blinks during communication with the PC
- Operating temperature 0 to 50 °C
- 2500 VRMS high isolation voltage (ST-LINK/V2-ISOL only)
پروگرامر ST-LINK/V2 (EN) اورجینال (کیفیت بالا و قابلیت آپدیت) نیز در فروشگاه موجود میباشد که از لینک زیر میتوانید مشاهده و خرید کنید.
نقدوبررسی محصول / پرسش و پاسخ
-
نقد و بررسی (2)
-
پرسشها و پاسخها (8)
-
Latest
-
Latest