السیدی 2.4 اینچ با تاچ TFT LCD 2.4 inch with touch -240x320 Parallel - ILI9341

السیدی 2.4 اینچ با تاچ TFT LCD 2.4 inch with touchبا رزولیشن 240x320 و ILI9341 و Parallel interface /  این محصول با تاچ می باشد.

Size: 2.4 inch
Control chip: ILI9341
Resolution: 240*320
Display area: 36.72 x 48.96(mm)
Physical size:42.72 (W) * 60.26 (H) * 3.75 +/- 0.1MAX(T)
Number of pins: 37Pin
Display color: full color
Pixel size: 0.153 x 0.153(mm)
temperature: -20~70  °c
voltage: 3.3V
Interface type: Parallel

1. PIN No.: 1-4, Symbol: DBO-DB3, Description: (No function when not in use), Notes: (Floating, connect to GND)
2. PIN No.: 5, Symbol: GND, Description: Ground, Notes: (Power supply for LCM (2.8-3.3V))
3. PIN No.: 6, Symbol: IOVCC, Description: (Power supply for I/O), Notes: (None)
4. PIN No.: 7, Symbol: /CS, Description: Chip select pin ("Low" enable), Notes: (The pin is used to select data/command in the parallel interface)
5. PIN No.: 8, Symbol: RS, Description: (When RS="1", data is selected (display data), When RS="0", command is selected), Notes: (None)
6. PIN No.: 9, Symbol: /WR, Description: Serves as a read signal and MCU read data at the rising edge, Notes: (When not in use, connect to IOVCC)
7. PIN No.: 10, Symbol: /RD, Description: Serves as a read signal and MCU read data at the rising edge, Notes: (When not in use, connect to IOVCC)
8. PIN No.: 11, Symbol: NC, Description: No connection, Notes: (None)
9. PIN No.: 12, Symbol: XL, Description: Touch panel control pin, Notes: (Touch panel X- coordinate)
10. PIN No.: 13, Symbol: XU, Description: Touch panel control pin, Notes: (Touch panel X+ coordinate)
11. PIN No.: 14, Symbol: YD, Description: Touch panel control pin, Notes: (Touch panel Y- coordinate)
12. PIN No.: 15, Symbol: YU, Description: Touch panel control pin, Notes: (Touch panel Y+ coordinate)

1. PIN No.: 16, Symbol: LEDA, Description: Anode of Backlight (3.0-3.4V Typical, 3.2V), Notes: (None)
2. PIN No.: 17, Symbol: LED1+, Description: Cathode of Backlight, Notes: (None)
3. PIN No.: 18, Symbol: LED1-, Description: Cathode of Backlight, Notes: (None)
4. PIN No.: 19, Symbol: LED2+, Description: Cathode of Backlight, Notes: (None)
5. PIN No.: 20, Symbol: LED2-, Description: Cathode of Backlight, Notes: (Power supply available)
6. PIN No.: 21, Symbol: FWMK, Description: Tearing effect output pin to synchronize MPU to frame writing, activated by SW command.
When this pin is not activated, this pin is low. If not used, open this pin, Notes: (None)
7. PIN No.: 22, Symbol: DB4, Description: Data bus (used when not in use), Notes: (None)
8. PIN No.: 23-30, Symbol: DB5-DB12, Description: Data bus (used when not in use), Notes: (None)
9. PIN No.: 31, Symbol: /RESET, Description: LCM reset pin, signal is active low, Notes: (Power supply for LCM (2.8-3.3V))
10. PIN No.: 32, Symbol: VCC, Description: Power supply for LCM (2.8-3.3V), Notes: (None)
11. PIN No.: 33, Symbol: IOVCC, Description: Power supply for I/O, Notes: (None)
12. PIN No.: 34, Symbol: GND, Description: Ground, Notes: (None)
13. PIN No.: 35-37, Symbol: DB13-DB15, Description: Data bus (used when not in use, fix to GND level), Notes: (None)

محتوای فایل مربوط به مثال و document: